---
title: Classic
product: SpeedTree Modeler
version: '10'
latest_version: '10'
status: This page documents version 10. The latest version is 10.
canonical: https://docs.unity.com/en-us/speedtree-modeler/10/classic-generation-mode
latest_url: https://docs.unity.com/en-us/speedtree-modeler/10/classic-generation-mode.md
last_updated: 2026-11-19
generated_at: 2026-11-19T15:06:02.582Z
locale: en-us
---

# Classic

> Classic mode exists to support legacy models.

Classic mode should not be used on current models. Favor [Interval](./interval-generation-mode.md), [Phyllotaxy](./phyllotaxy-generation-mode.md), and [Bifurcation](./bifurcation-generation-mode.md) instead.

## Style

### Absolute

For **Generation:Frequency** and **Steps:Number**, the exact value you enter will be set.

For example, if **Generation:Frequency** is 3, then 3 nodes will appear. If you then change the **Steps:Number** to 3, you will get 3 steps on the spine with 3 nodes in each step.

### Relative

**Generation:Frequency** and **Steps:Number** values are computed based on the length of the parent node.

For example, if **Generation:Style** is set to relative, this integer becomes a floating point value and the actual number of nodes generated is computed based on the length of the parent. So, if both the **Generation:Frequency** and the **Steps:Number** is set to 3, you will get 3 steps on the spine with 3 nodes in each step for the spine length value you have set. However, if the branches are shorter or longer, the node amount for **Generation:Frequency** and **Steps:Number** may vary: fewer nodes for a short spine length and more nodes for a longer spine length.

### Frequency

Sets the number of nodes generated.

## Orientation

### Alignment

Specifies how the local up axis aligns with the global up vector from the following options:

| **Property**     | **Description**                                                                  |
| ---------------- | -------------------------------------------------------------------------------- |
| **None**         | Nodes have a random orientation.                                                 |
| **Align**        | The first node in each step is centered vertically on its parent.                |
| **Center Align** | Each step is re-aligned so the Sweep range is centered vertically on its parent. |

> **Note:**
>
> If 'Steps' are disabled, the initial generation angle is centered vertically on the parent node instead.

#### Balanced

Nodes can be balanced (equally spaced) radially by enabling this property.

> **Note:**
>
> Changing the **Generation:Frequency** or **Generation:Steps:Number** properties will result in positional shifting in order to maintain equal spacing.

### Offset

The computed angle for each node is offset \[+/-] between 0 and this amount.

### Sweep

Defines the arc around the parent node where nodes are eligible.

> **Note:**
>
> Balance is applied after the **Sweep** arc is defined.

### Roll

Each node is rotated this absolute amount from its computed angle.

## Steps

### Enabled

When enabled, nodes are grouped into lengthwise steps along the parent node. Balance, angle offset, and other properties will be applied per step.

Each step contains approximately (Generation: Frequency ÷ Generation: Step: Number) branches.

### Number

Determines the number of steps to distribute the computed frequency among.

> **Note:**
>
> If **Generation:Style** is set to relative, the actual number of steps generated is computed based on the length of the parent node.

### Spread

The maximum amount of lengthwise node spacing allowed from the center of each step to its extents.

### Roll

The amount each step is rolled relative to the previous step.

### Per Step Frequency

The number of nodes from the **Generation:Frequency** value is created per step, rather than the frequency value being distributed among all the steps.

## Shared

The **Shared** properties are common to all generation modes and are documented [here](./generation-properties.md#common).
